Search GrainBench

Find plans, patterns, guides, materials and tools.

The Fresh Start Bathroom Shelf project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Fresh Start Bathroom Shelf

A wall shelf with two shelves and a towel bar below, hung on two hidden rails screwed into the wall studs.

24 in W × 7-3/4 in D × 20 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x8 and 1x3 boards, 1/2 in plywood and 3/4 dowel.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x8 board, 8 ft: For H shelves, S sides
  • 1 x 1x3 board, 4 ft: For R mounting rails
  • 1 x 3/4 dowel, 3 ft (or an offcut at least 24-7/16 in long): For D towel bar
  • 1 x 1/2 plywood, 2 ft x 2 ft panel: For B back
  • 1-1/4 in coarse-thread pocket-hole screws: 20, plus a few spares
  • #6 x 1 in flathead wood screws: 16, plus a few spares
  • #10 x 3-1/2 in cabinet screws: 4 washer-head screws for wood studs behind 1/2 in drywall
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 500 mL (1 pint) of semi-gloss paint or moisture-resistant clear finish

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver with a countersink bit; 3/4 in Forstner bit with a depth stop; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 24 in; Stud finder and a level; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Use a moisture-resistant finish on every face, including the back and cut ends. A hardwood dowel makes the stiffest towel bar. Cut the sides, shelves and rails square. Cut the back B to 24 x 20 in and the towel bar D to 23-7/16 in so it can turn in its sockets.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

8 parts from 1x8, 1x3, 1/2 plywood and 3/4 dowel.

IDPartQtyStockLengthWidthThickness
SSides21x8207-1/43/4
HShelves21x822-1/27-1/43/4
RMounting rails21x322-1/22-1/23/4
BBack11/2 plywood24201/2
DTowel bar13/4 dowel23-7/163/43/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the holes

On the inside face of each S, mark the bar centre 3 in up and 3-5/8 in from the front, and drill a 3/4 in socket 1/2 in deep. Then drill the pocket holes: 3 at each end of both H on the underside and 2 at each end of both R on the back face.

02 Build the case

Glue and screw the shelves and rails to the first S: shelf undersides at 7 and 19-1/4 in, rail bottoms at 9 and 14-1/2 in, rails flush with the back edge. Drop D into its socket without glue, then fit the second side over the free ends and the bar and drive the rest of the screws.

03 Attach the back

Square the case and screw B onto the back edges with 16 screws, about every 6 in, keeping clear of the pocket screws.

04 Finish

Sand and finish every surface to resist steam, including the back and the ends of the bar.

05 Hang it

Find two studs. Hold the shelf level and drill through the back and each rail at both studs, so you have 4 holes. Drive the 4 cabinet screws until snug.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Everyday Bookshelf project visualization

SHELVES & STORAGE · CONFIDENT BEGINNER

The Everyday Bookshelf

A sturdy three-shelf bookcase with a recessed base rail and a thin plywood back that keeps it square. It is built from 1x12 boards with pocket screws, and anchors to the wall.

↔︎ 30 × 11-1/2 × 48 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.