Search GrainBench

Find plans, patterns, guides, materials and tools.

The Reading Corner Book Bin project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Reading Corner Book Bin

A low, open floor bin that shows off picture books face-out. Sloping sides make it easy for small hands to reach in.

22 in W × 12 in D × 16 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x6 board and 3/4 in plywood.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x6 board, 4 ft (or an offcut at least 21-1/2 in long): For F front lip
  • 1 x 3/4 plywood, 4 ft x 4 ft panel: For B bottom, R back, S sides (cut to a slope)
  • #8 x 1-1/2 in flathead wood screws: 22, plus a few spares
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 500 mL (1 pint) of low-odour, child-safe paint or clear finish
  • Felt pads (optional): 4

Before the first cut

Circular saw with a straight-edge guide, or have the store cut the plywood; Jigsaw for the angled and shaped cuts; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 24 in; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Use smooth plywood with a good face. All the plywood parts fit on a 4 x 4 ft panel. Cut the two side blanks S as 16 x 12 in rectangles; the slope comes in step 1. Cut the bottom, back and lip square.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

5 parts from 3/4 plywood and 1x6.

IDPartQtyStockLengthWidthThickness
SSides (cut to a slope)23/4 plywood16123/4
BBottom13/4 plywood20-1/2123/4
RBack13/4 plywood20-1/215-1/43/4
FFront lip11x620-1/25-1/23/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Cut the sloped sides

Clamp both S blanks together. Mark 6-1/4 in up on the front edge and 16 in (the full height) at the back, join the marks, and cut both at once so they match.

02 Fit the bottom and back

Glue the ends of B, clamp it between the sides flush at the bottom, and drive 3 screws through each side into it. Stand R on B at the back, glue, and drive 3 screws through each side and 3 up through B.

03 Add the front lip

Fit F on B at the front between the sides. Glue, drive 2 screws through each side and 3 up through the bottom.

04 Finish

Round every edge and corner well, sand smooth, and apply your finish.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Everyday Bookshelf project visualization

SHELVES & STORAGE · CONFIDENT BEGINNER

The Everyday Bookshelf

A sturdy three-shelf bookcase with a recessed base rail and a thin plywood back that keeps it square. It is built from 1x12 boards with pocket screws, and anchors to the wall.

↔︎ 30 × 11-1/2 × 48 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.