Search GrainBench

Find plans, patterns, guides, materials and tools.

The Quiet Morning Lap Desk project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Quiet Morning Lap Desk

A plywood lap desk that straddles your legs on the couch or in bed, with a rear brace that keeps it square.

24 in W × 14-1/2 in D × 9-1/4 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x3 board and 3/4 in plywood.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x3 board, 4 ft (or an offcut at least 22 in long): For R rear brace
  • 1 x 3/4 plywood, 2 ft x 4 ft panel: For S sides, T top
  • 1-1/4 in coarse-thread pocket-hole screws: 12, plus a few spares
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane
  • Felt strips (optional): 2, for the side bottoms

Before the first cut

Circular saw with a straight-edge guide, or have the store cut the plywood; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 24 in; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

All three plywood parts fit on a 2 x 4 ft project panel. Measure the space you will straddle; the clear width between the sides is 21 in and the height under the top is 8-1/2 in. Cut the top T and both sides S, checking that the sides are the same height so the desk sits level.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

4 parts from 3/4 plywood and 1x3.

IDPartQtyStockLengthWidthThickness
TTop13/4 plywood2414-1/23/4
SSides23/4 plywood8-1/214-1/23/4
RRear brace11x3212-1/23/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the pocket holes

Drill 4 pocket holes along the top edge of each S on the inside face, and 2 at each end of R on its back face.

02 Fit the brace

Glue and clamp R between the two sides at the back, flush with their tops and back edges, and drive 4 screws. The outside width should be 22-1/2 in.

03 Attach the top

Lay T face down, centre the frame on it with 3/4 in overhang at each end, flush front and back, and drive the 8 screws into the top.

04 Finish

Round all the edges, sand, seal the plywood edges with your finish, and add felt strips under the sides.

A little help along the way

Read the drawings and cut listChoose plywood for the desktop

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Quiet Corner Side Table project visualization

TABLES · CONFIDENT BEGINNER

The Quiet Corner Side Table

A simple side table with square legs, a shallow apron and a three-board top. The top boards are joined with pocket screws instead of a full glue-up, so there is no ripping or planing.

↔︎ 22 × 16-1/2 × 24 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.