Search GrainBench

Find plans, patterns, guides, materials and tools.

The Little Green Raised Bed project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Little Green Raised Bed

A small open-bottom raised bed, two boards high, with corner posts inside. Six 1x6 boards and a 2x2 make the whole thing.

36 in W × 24 in D × 11 in H

BeginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x6 board and 2x2 lumber.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 2 x 1x6 board, 8 ft: For A long boards, E end boards
  • 1 x 1x6 board, 4 ft: For E end boards
  • 1 x 2x2 board, 4 ft: For P corner posts
  • #8 x 2 in exterior wood screws: 32, plus a few spares

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 24 in; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Use untreated cedar or another naturally rot-resistant wood for growing food. A 1x6 is actually about 3/4 x 5-1/2 in. Cut the long boards A and the end boards E square, and the four posts P.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

12 parts from 1x6 and 2x2.

IDPartQtyStockLengthWidthThickness
ALong boards41x6365-1/23/4
EEnd boards41x622-1/25-1/23/4
PCorner posts42x2101-1/21-1/2

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Build the long walls

Lay two A boards edge to edge. Set a P 3/4 in in from each end, flush with the bottom edge. Drill and drive 2 screws through each board end into the post, 8 per wall. Make the second long wall.

02 Add the ends

Stand the long walls up, fit the E boards between them at each end, clamp it square and drive 2 screws through each board end into the posts, offset 3/4 in from the first set.

03 Set it in place

Level the ground, clear weeds, set the bed down with its whole bottom edge resting on soil, and fill it gradually.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Garden Peg Rack project visualization

OUTDOOR & GARDEN · CONFIDENT BEGINNER

The Garden Peg Rack

A wall board with four round pegs for hand tools, hats and twine in a shed or garage. The pegs are glued into shallow sockets and locked in with a screw from behind.

↔︎ 32 × 5-1/2 × 5-1/2 in✓ Cut list

View plan & download

Quick PDFDownload

The Everyday Shoe Rack project visualization

SHELVES & STORAGE · BEGINNER

The Everyday Shoe Rack

A low entryway rack with a lower shelf for everyday shoes and a top that overhangs the sides. It comes from one 8 ft 1x12 and a short 1x3, joined with pocket screws.

↔︎ 30 × 11-1/4 × 18 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.