Search GrainBench

Find plans, patterns, guides, materials and tools.

The Garden Peg Rack project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Garden Peg Rack

A wall board with four round pegs for hand tools, hats and twine in a shed or garage. The pegs are glued into shallow sockets and locked in with a screw from behind.

32 in W × 5-1/2 in D × 5-1/2 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x6 board and 3/4 dowel.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x6 board, 4 ft: For B mounting board
  • 1 x 3/4 dowel, 3 ft (or an offcut at least 22-3/8 in long): For P pegs
  • #8 x 1-1/2 in flathead wood screws: 4, plus a few spares
  • #10 x 3 in cabinet screws: 4 washer-head screws for wood studs behind 1/2 in drywall
  • Exterior wood glue: Small bottle, rated for outdoor use
  • Sandpaper: 120 and 180 grit
  • Finish: About 250 mL (half a pint) of exterior paint or exterior clear finish

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver; 3/4 in Forstner or spade bit with a depth stop (or tape on the bit); Tape measure, pencil and a combination or speed square; Stud finder and a level; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Pick a flat 1x6 without knots where the pegs go. Hardwood dowel is stronger than the softwood kind. Cut the board B square to 32 in and the four pegs P to 5-1/4 in. Sand a small bevel on the outer end of each peg.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

5 parts from 1x6 and 3/4 dowel.

IDPartQtyStockLengthWidthThickness
BMounting board11x6325-1/23/4
PPegs43/4 dowel5-1/43/43/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the sockets

Mark the peg centres along the middle of B at 4, 12, 20 and 28 in from the left end. Clamp the board to scrap and drill each socket 1/2 in deep with the 3/4 in bit, keeping the drill square to the face. Then drill a small pilot from the back of the board at the centre of each socket.

02 Glue in the pegs

Try each P in its socket first. Spread glue in the socket and on the peg end, push it fully home and keep it square while the glue sets.

03 Lock the pegs

Once the glue has set, drive a #8 x 1-1/2 in screw from the back of the board into the end of each peg. Snug, not tight.

04 Finish

Sand, round the board edges, and apply an exterior finish, including the back and ends.

05 Hang the rack

Find two studs behind where the rack will go. Hold it level, drill 2 holes through the board at each stud, clear of the pegs, and drive the 4 cabinet screws.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.