
GRAINBENCH ORIGINALS
The Quiet Corner Dressing Table
A compact dressing table with a plywood top and a shallow centre drawer on ball-bearing slides. The drawer sits in a neat inset opening.
42 in W × 16 in D × 30 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x4, 1x2 and 1x3 boards, 2x2 lumber, 3/4 in plywood and 1/4 in plywood.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 2x2 board, 8 ft: For L legs
- 1 x 2x2 board, 4 ft: For L legs
- 1 x 1x4 board, 6 ft: For A back apron, E end aprons
- 1 x 1x2 board, 8 ft: For F front rails
- 1 x 1x3 board, 6 ft: For N drawer front and back, S drawer sides
- 1 x 3/4 plywood, 2 ft x 4 ft panel: For D drawer face, G drawer guides, I front infills, T top
- 1 x 1/4 plywood, 2 ft x 2 ft panel (or an offcut at least 10-1/2 x 14-15/16 in): For B drawer bottom
- 1-1/4 in coarse-thread pocket-hole screws: 41, plus a few spares
- #6 x 1-1/4 in flathead wood screws: 12, plus a few spares
- #4 x 5/8 in screws: 10, for the drawer bottom
- Drawer slides: 1 pair of 10 in side-mount slides (KV 8400 or similar), with their screws
- Knob: 1, with a screw to suit the 1-1/2 in front
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
- Finish: About 1 L (1 quart) of paint, stain or clear water-based polyurethane
- Anti-tip strap: 1, with screws suited to your wall
Before the first cut
Circular saw with a straight-edge guide, or have the store cut the plywood; Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 4 clamps that open to at least 24 in; Sander or sanding block; Safety glasses and hearing protection.
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
Choose smooth cabinet plywood for the top and drawer face. Buy the slides before cutting the drawer parts, and measure the finished opening before cutting N and B. Cut the legs together so they match. Cut the table parts first; leave the drawer front, back and bottom (N and B) until the guides are in and you can measure the opening.
undefined
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
20 parts from 3/4 plywood, 2x2, 1x4, 1x2, 1x3 and 1/4 plywood.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| T | Top | 1 | 3/4 plywood | 42 | 16 | 3/4 |
| L | Legs | 4 | 2x2 | 29-1/4 | 1-1/2 | 1-1/2 |
| A | Back apron | 1 | 1x4 | 37 | 3-1/2 | 3/4 |
| E | End aprons | 2 | 1x4 | 11 | 3-1/2 | 3/4 |
| F | Front rails | 2 | 1x2 | 37 | 1-1/2 | 3/4 |
| I | Front infills | 2 | 3/4 plywood | 10-1/2 | 3 | 3/4 |
| G | Drawer guides | 2 | 3/4 plywood | 11-3/4 | 6 | 3/4 |
| S | Drawer sides | 2 | 1x3 | 10-1/2 | 2-1/2 | 3/4 |
| N | Drawer front and back | 2 | 1x3 | 13-7/16 | 2-1/2 | 3/4 |
| B | Drawer bottom | 1 | 1/4 plywood | 14-15/16 | 10-1/2 | 1/4 |
| D | Drawer face | 1 | 3/4 plywood | 15-3/4 | 2-3/4 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Drill the pocket holes
Drill 2 holes at each end of A and both E, and 1 at each end of both F, all on the hidden face. On each G, drill 2 at the front edge and 2 at the back edge on the outside face. Add top holes for the desktop: 3 along A, 2 along each E and 3 along each G. Each I gets 1 hole toward its leg and 1 up toward the top rail.
02 Build two end frames
Clamp an E between a front and back leg, flush with the leg tops and 3/8 in in from the outside. Glue and drive 4 screws. Make the second frame the same way.
03 Join with the back apron and front rails
Fit A at the back, flush on top and 3/8 in in, with 4 screws. Fit the upper F flush with the leg tops and the lower F with its bottom 6 in below them, leaving a 3 in gap. Drive 1 screw at each rail end and check the diagonals.
04 Fit the drawer guides
Mark the inside faces of the guides 10-1/2 and 26-1/2 in from the inside of the left leg, so they are 16 in apart. Fit each G between the front rails and the back apron, flush on top, and drive 2 screws into each.
05 Fill in the front
Glue each I between the rails on either side of the opening, front faces flush, and drive its 2 screws. The opening should be 16 x 3 in.
06 Attach the top
Lay T face down, centre the frame on it with 1 in overhang all round, and drive the 13 top screws.
07 Build the drawer box
Measure the opening between the guides and subtract 1-1/16 in for the slides; with a 16 in opening the box is 14-15/16 in wide. Cut N and B to suit. Glue N between the two S and drive 2 screws at each corner through the sides. Glue and screw B underneath with 10 small screws.
08 Fit the slides
Mount the slides on the guides and the drawer following the slide maker's instructions, keeping the box 1/8 in above the lower rail. Check it runs smoothly.
09 Fit the drawer face
Close the drawer and hold D in the opening with 1/8 in spacers on all four sides. Clamp it to the drawer front and drive 4 screws from inside the drawer. Drill for the knob and fit it.
10 Finish and anchor
Take out the drawer, sand, and finish everything, keeping finish off the slides. Fasten the anti-tip strap into a wall stud.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

TABLES · CONFIDENT BEGINNER
The Quiet Corner Side Table
A simple side table with square legs, a shallow apron and a three-board top. The top boards are joined with pocket screws instead of a full glue-up, so there is no ripping or planing.
↔︎ 22 × 16-1/2 × 24 in✓ Cut list
View plan & downloadQuick PDFDownload

TABLES · CONFIDENT BEGINNER
The Easy Sunday Coffee Table
A clean, low coffee table with square legs and a four-board top. Plain 1x6 boards are joined with pocket screws, so the top needs no ripping or planing.
↔︎ 42 × 22 × 18 in✓ Cut list
View plan & downloadQuick PDFDownload

TABLES · CONFIDENT BEGINNER
The Welcome Home Console
A slim hall console with a one-board top and a low rear rail that stiffens the base. It sits close to the wall and is anchored to it.
↔︎ 40 × 11-1/4 × 30 in✓ Cut list
View plan & downloadQuick PDFDownload