Search GrainBench

Find plans, patterns, guides, materials and tools.

The Weekday Writing Desk project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Weekday Writing Desk

A simple writing desk with a smooth plywood top, square legs and low side stretchers that keep it steady while leaving open legroom.

42 in W × 22 in D × 30 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x4 and 1x3 boards, 2x2 lumber and 3/4 in plywood.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 2x2 board, 8 ft: For L legs
  • 1 x 2x2 board, 4 ft: For L legs
  • 1 x 1x4 board, 8 ft: For A front and back aprons, B side aprons
  • 1 x 1x4 board, 4 ft (or an offcut at least 16 in long): For B side aprons
  • 1 x 1x3 board, 4 ft: For E side stretchers
  • 1 x 3/4 plywood, 2 ft x 4 ft panel: For T top
  • 1-1/4 in coarse-thread pocket-hole screws: 34, plus a few spares
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 1 L (1 quart) of paint, stain or clear water-based polyurethane
  • Felt pads (optional): 4

Before the first cut

Circular saw with a straight-edge guide, or have the store cut the plywood; Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 36 in; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Choose cabinet-grade plywood with a smooth face for the top; a 2 x 4 ft project panel is enough. Pick legs without twist. Cut the four legs together so they match. Cut the top to 42 x 22 in and check its diagonals.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

11 parts from 3/4 plywood, 2x2, 1x4 and 1x3.

IDPartQtyStockLengthWidthThickness
TTop13/4 plywood42223/4
LLegs42x229-1/41-1/21-1/2
AFront and back aprons21x4353-1/23/4
BSide aprons21x4153-1/23/4
ESide stretchers21x3152-1/23/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the pocket holes

Drill 2 pocket holes at each end of every A, B and E on the inside face. Then add holes along the top edge for the desktop: 3 in each A and 2 in each B, also on the inside face.

02 Build two end frames

Clamp a B between two L with the tops flush and set 1/4 in in from the leg faces, glue and drive 4 screws. Mark the legs 6 in up from the floor, fit an E on the marks with the same setback, and drive 4 more. Make the second frame the same way.

03 Join the frames

Fit the two A between the end frames with the same setback and flush tops. Glue, clamp and drive 8 screws. Check the diagonals match and all four feet sit flat.

04 Attach the top

Lay T good face down on a blanket. Centre the base on it upside down with a 2 in overhang all round, clamp, and drive the 10 screws from the apron top edges into the top.

05 Finish

Sand with 120 then 180 grit, ease the edges of the top, and apply your finish.

A little help along the way

Read the drawings and cut listChoose plywood for the desktop

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Quiet Corner Side Table project visualization

TABLES · CONFIDENT BEGINNER

The Quiet Corner Side Table

A simple side table with square legs, a shallow apron and a three-board top. The top boards are joined with pocket screws instead of a full glue-up, so there is no ripping or planing.

↔︎ 22 × 16-1/2 × 24 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.