Search GrainBench

Find plans, patterns, guides, materials and tools.

The Weekend Assembly Table project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Weekend Assembly Table

A simple assembly table with square legs, 2x4 rails on all four sides at both levels, and two supported plywood panels.

48 in W × 24 in D × 34 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

4x4 and 2x4 lumber and 3/4 in plywood.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 2 x 4x4 board, 8 ft: For L square legs
  • 3 x 2x4 board, 8 ft: For A front and back rails, E end rails
  • 1 x 3/4 plywood, 4 ft x 8 ft sheet: For B lower shelf blank - 4 notches, T worktop
  • 2-1/2 in coarse-thread pocket-hole screws: 32 used; buy a box of 50 for setup and spares
  • #8 x 1-1/2 in flathead wood screws: 24 used; buy a box of 50 for setup and spares
  • Wood glue: One small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 1 L (1 quart), depending on coverage; coat all faces and cut edges

Before the first cut

Saw and supported setup suitable for the square posts and 2x4 rails; Circular saw with straight-edge guide for plywood, or store-cut blanks; Jigsaw for the leg notches; Pocket-hole jig for 1-1/2 in stock, stepped bit, stop collar and long driver; Drill/driver, suitable pilot and countersink bits; Tape, pencil, square, straightedge and clamps opening at least 48 in; Sanding tools, eye/hearing protection and dust protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Use straight, dry softwood for the posts and all 2x4 rails, plus flat 3/4 in plywood. Square posts are nominal 4x4; measure their actual faces before marking notches. The light plywood colouring is for material clarity, not a required stain. Buy one full 4 x 8 ft plywood sheet: two 48 x 24 in panels do not fit one 4 x 4 ft panel once a saw kerf is included. Follow the cutting layout below and check each factory edge used for a 48 in dimension is straight and actually 48 in. If it is undersize or must be trimmed, obtain an oversize panel rather than quietly reducing the finished table. Finished dimensions are below. Square one end, cut matching pieces together and label every part. Cutting layouts allow 1 in of end trimming per board and 1/8 in saw kerfs. Mark the front and top edges before drilling. Use offcuts only if they are sound, straight and large enough for the stated cutting allowance.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

14 parts from 4x4, 2x4 and 3/4 plywood.

IDPartQtyStockLengthWidthThickness
LSquare legs44x433-1/43-1/23-1/2
AFront and back rails42x4413-1/21-1/2
EEnd rails42x4173-1/21-1/2
BLower shelf blank - 4 notches13/4 plywood48243/4
TWorktop13/4 plywood48243/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Cut, label and drill the rails

Cut the four matching legs together; label the eight rails and keep their top edges marked. Set the jig and stop for 1-1/2 in stock. Drill 2 pockets at each end of every A and E on the inward face, at 7/8 and 2-5/8 in below its top edge. Use 2-1/2 in pocket screws throughout the frame. Test the setting on matching scrap before drilling the project rails.

02 Build the two lower end frames

Pair two L legs for each end frame. Mark each leg 4 in up from the bottom; place a lower E with its bottom on the marks and its outside face flush with the post outside faces. Clamp square, glue the rail ends and drive 2 pocket screws into each leg, 4 per rail. Keep all pocket entries facing inward. Check both lower E rails finish at the same height.

03 Join the lower frame

Stand the end frames on a flat surface and fit the two lower A between them. Keep the lower A bottom edges at the same 4 in marks, with outside faces flush with the posts. Clamp, glue and drive 2 pocket screws at each end, 8 for the pair. Leave all upper rails off. Match the diagonal measurements and check all four feet sit flat.

04 Cut and dry-fit the shelf notches

Cut B as a 48 x 24 in blank and mark four corner notches around the actual legs. Each nominal notch is 3-1/2 x 3-1/2 in; remove only these four corners. Jigsaw inside the waste, then ease each cut to the marked line and allow only the sliding/finish clearance needed around the posts. Dry-fit every notch against the actual stock before sealing the cut edges.

05 Install the shelf before the upper rails

Lower B over the four leg tops while the upper frame is still open. The underside must rest directly on all four lower rails at 7-1/2 in, with its outside edges aligned to the post outside faces. Keep the notches around the posts; do not force the plywood or enlarge a notch to compensate for a misplaced rail. Clamp the panel flat. Check rail bearing around every edge and recheck the frame diagonals.

06 Fix the shelf to all four rails

Mark the fixing positions shown below on B. Keep every pilot centred over its receiving rail; the dots are measured from the front-left corner of the original blank. Predrill and countersink for 12 of the 1-1/2 in flathead screws, 3 into each rail. Drive heads just flush; do not use the long pocket screws through plywood. Check the plywood stays flat and no screw head is buried below the face.

07 Fit the four upper rails

Fit the remaining two E and two A between the legs. Mark their bottom edges 29-3/4 in above the ground; the rail tops must be level with the leg tops at 33-1/4 in, and outside faces must stay flush. Clamp square, glue and drive 2 pocket screws per rail end, 16 screws for these four rails. Lay a straightedge across the frame and check every top edge is level before fitting T.

08 Fit the supported plywood worktop

Set the unnotched T panel onto the upper rails and four leg tops. Align it flush all around: its top finishes 34 in above the ground, with no unsupported end overhang. Clamp, mark the same 12 fixing coordinates used for B, predrill/countersink and install the remaining twelve 1-1/2 in panel screws. Check both end rails sit immediately beneath the tabletop edges and all heads finish flush.

09 Finish and check the table

Ease the plywood edges and sand to 180 grit. Seal all faces, undersides, notch cuts and leg ends; follow glue and finish cure times. Inspect square, level, panel bearing and screw tips. This is an assembly table, not a seat, step or rated machine stand.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Maker's Clamp Rack project visualization

WORKSHOP · CONFIDENT BEGINNER

The Maker's Clamp Rack

A wall shelf with six open slots that holds bar clamps by their heads. The slotted shelf is plywood, so the fingers between slots are strong in every direction.

↔︎ 32 × 7-1/4 × 8 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.