
GRAINBENCH ORIGINALS
The Maker's Clamp Rack
A wall shelf with six open slots that holds bar clamps by their heads. The slotted shelf is plywood, so the fingers between slots are strong in every direction.
32 in W × 7-1/4 in D × 8 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x8 board and 3/4 in plywood.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 1x8 board, 4 ft: For B wall board
- 1 x 3/4 plywood, 2 ft x 4 ft panel: For G brackets (triangles), S slotted shelf
- #8 x 1-1/2 in flathead wood screws: 24, plus a few spares
- #10 x 3 in cabinet screws: 4 washer-head screws for wood studs behind 1/2 in drywall
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
Before the first cut
Circular saw with a straight-edge guide, or have the store cut the plywood; Jigsaw for the angled and shaped cuts; Drill/driver with a 1/2 in bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 12 in; Stud finder and a level; Safety glasses and hearing protection.
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
The shelf and brackets come from a 2 x 4 ft panel of 3/4 in plywood. Plywood is used for the shelf because the slots would leave solid wood fingers that can split along the grain. Cut the wall board B and the shelf S to 32 x 7-1/4 in. For the brackets G, cut two 6-1/2 in plywood squares and saw each corner to corner; that gives four triangles, so you have one spare.
For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
5 parts from 1x8 and 3/4 plywood.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| B | Wall board | 1 | 1x8 | 32 | 7-1/4 | 3/4 |
| S | Slotted shelf | 1 | 3/4 plywood | 32 | 7-1/4 | 3/4 |
| G | Brackets (triangles) | 3 | 3/4 plywood | 6-1/2 | 6-1/2 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Cut the slots
Test one of your clamps in a slot cut in scrap first. On S, mark six slots along the front edge, 1/2 in wide and 4-1/2 in deep, centred 4, 8, 12, 20, 24 and 28 in from the left. Drill a 1/2 in hole at the inner end of each, then saw the two sides from the front edge into the hole.
02 Attach the brackets
Glue each G to the front of B with its square corner up and its top flush with the top of the board, at 1-1/2, 15-5/8 and 29-3/4 in from the left. Drive 3 screws through the back of B into each bracket.
03 Add the shelf
Set S on top, back edges flush. Drive 3 screws down into each bracket and 6 into the top edge of B, keeping clear of the slots.
04 Hang it
Find two studs within the board. Hold the rack level and drive 2 cabinet screws through B into each stud, one near the top and one near the bottom, clear of the brackets.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

WORKSHOP · CONFIDENT BEGINNER
The Neat Cut Scrap Bin
A sturdy plywood floor bin with two bays and sloped sides for keeping offcuts sorted and easy to see.
↔︎ 24 × 18 × 28 in✓ Cut list
View plan & downloadQuick PDFDownload

WORKSHOP · CONFIDENT BEGINNER
The Small Workshop Pegboard
A 2 ft square pegboard on a 1x3 frame, with spacer blocks behind so hooks have room and mounting screws reach the studs.
↔︎ 24 × 2-1/2 × 24 in✓ Cut list
View plan & downloadQuick PDFDownload

WORKSHOP · CONFIDENT BEGINNER
The Weekend Assembly Table
A simple assembly table with square legs, 2x4 rails on all four sides at both levels, and two supported plywood panels.
↔︎ 48 × 24 × 34 in✓ Cut list
View plan & downloadQuick PDFDownload