Search GrainBench

Find plans, patterns, guides, materials and tools.

The Small Workshop Pegboard project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Small Workshop Pegboard

A 2 ft square pegboard on a 1x3 frame, with spacer blocks behind so hooks have room and mounting screws reach the studs.

24 in W × 2-1/2 in D × 24 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x3 board, 2x2 lumber and 1/4 in pegboard.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x3 board, 8 ft: For H top and bottom rails, S side rails
  • 1 x 2x2 board, 4 ft (or an offcut at least 13-3/8 in long): For B spacer blocks
  • 1 x 1/4 pegboard, 2 ft x 4 ft panel: For P pegboard
  • 1-1/4 in coarse-thread pocket-hole screws: 4, plus a few spares
  • #8 x 1-1/2 in flathead wood screws: 8, plus a few spares
  • #6 x 3/4 in flathead wood screws: 14, plus a few spares
  • #10 x 4-1/2 in wood screws: 4, with washers, for wood studs behind 1/2 in drywall
  • Pegboard hooks: A starter set to suit the hole size

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 30 in; Stud finder and a level; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Pegboard is usually sold in 2 x 4 ft panels; cut a 2 ft square from it. Check that your hooks fit its hole size (1/4 in holes are most common). Cut the pegboard P to 24 x 24 in, the rails H and S square, and the four spacer blocks B.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

9 parts from 1/4 pegboard, 1x3 and 2x2.

IDPartQtyStockLengthWidthThickness
PPegboard11/4 pegboard24241/4
HTop and bottom rails21x3242-1/23/4
SSide rails21x3192-1/23/4
BSpacer blocks42x231-1/21-1/2

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Build the frame

Drill 1 pocket hole at each end of both S on the back face. Glue and clamp them between the two H to make a 24 in square and drive 4 screws. Check the diagonals match.

02 Add the spacer blocks

On the back of each H, mark block positions 2-1/2 and 18-1/2 in from the left end so the blocks are 16 in apart, centre to centre. Glue and screw each B on with 2 screws.

03 Attach the pegboard

Lay P on the front of the frame, flush at all four edges. Drive 4 screws through it into each H and 3 into each S, on the solid board between the holes.

04 Hang the board

Find two studs 16 in apart. Hold the board level with the blocks over the studs and drive one long screw through each block into a stud, through a pegboard hole if one lines up.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Maker's Clamp Rack project visualization

WORKSHOP · CONFIDENT BEGINNER

The Maker's Clamp Rack

A wall shelf with six open slots that holds bar clamps by their heads. The slotted shelf is plywood, so the fingers between slots are strong in every direction.

↔︎ 32 × 7-1/4 × 8 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.