Search GrainBench

Find plans, patterns, guides, materials and tools.

The Picnic Bottle Caddy project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Picnic Bottle Caddy

An open carrier with a round dowel handle for bottles, condiments or craft supplies.

12 in W × 7-1/4 in D × 10-1/2 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x8 and 1x3 boards and 1 dowel.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x8 board, 4 ft: For B bottom, E ends
  • 1 x 1x3 board, 4 ft (or an offcut at least 22-1/8 in long): For R side rails
  • 1 x 1 dowel, 3 ft (or an offcut at least 12-1/2 in long): For H handle
  • 1-1/4 in coarse-thread pocket-hole screws: 14, plus a few spares
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver; 1 in Forstner bit with a depth stop; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 18 in; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

A 1x8 is actually about 3/4 x 7-1/4 in. Choose a hardwood dowel for the handle. Cut the two ends E and the bottom B from the 1x8, the rails R from the 1x3 and the handle H from the dowel.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

6 parts from 1x8, 1x3 and 1 dowel.

IDPartQtyStockLengthWidthThickness
EEnds21x810-1/27-1/43/4
BBottom11x810-1/27-1/43/4
RSide rails21x310-1/22-1/23/4
HHandle11 dowel11-1/211

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the holes

On the inside face of each E, mark the handle centre 8-3/4 in up and 3-5/8 in from the front edge and drill a 1 in socket 1/2 in deep. Then drill the pocket holes: 3 at each end of B on the underside and 2 at each end of both R on the inside face.

02 Attach to the first end

Glue and clamp B to the first E, flush at the bottom and front, and drive 3 screws. Stand both R on B at the front and back, glue, and drive 2 screws each.

03 Add the handle and second end

Put a little glue in both sockets, seat H in the first end, then fit the second E over the handle and against the free ends. Clamp and drive the last 7 screws.

04 Finish

Sand, round the handle and top edges, and apply your finish.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Kitchen Recipe Box project visualization

SHELVES & STORAGE · CONFIDENT BEGINNER

The Kitchen Recipe Box

A small lift-off-lid box for 4 x 6 or 3 x 5 recipe cards. Two cleats under the lid keep it centred, and a plywood bottom is glued on underneath.

↔︎ 9 × 6 × 6-1/4 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.