
GRAINBENCH ORIGINALS
The Evening Charging Valet
A shallow tray for phones, keys and a watch, with a backstop drilled for charging cables. The chargers stay outside the tray.
12 in W × 7-1/4 in D × 4-1/4 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x8, 1x4 and 1x2 boards.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 1x8 board, 4 ft (or an offcut at least 13 in long): For B base
- 1 x 1x4 board, 4 ft (or an offcut at least 13 in long): For R backstop
- 1 x 1x2 board, 4 ft (or an offcut at least 24-3/4 in long): For F front lip, S side lips
- #8 x 1-1/2 in flathead wood screws: 10, plus a few spares
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
- Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane
- Cable grommets (optional): 2, sized to the holes
Before the first cut
Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver with a countersink bit; 3/4 in Forstner or spade bit (or the size your cable plug needs); Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 12 in; Sander or sanding block; Safety glasses and hearing protection.
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
Every part is short, so offcuts work well. Cut all the parts square. Check that your cable plugs fit through a 3/4 in hole before drilling R.
For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
5 parts from 1x8, 1x4 and 1x2.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| B | Base | 1 | 1x8 | 12 | 7-1/4 | 3/4 |
| R | Backstop | 1 | 1x4 | 12 | 3-1/2 | 3/4 |
| F | Front lip | 1 | 1x2 | 12 | 1-1/2 | 3/4 |
| S | Side lips | 2 | 1x2 | 5-3/4 | 1-1/2 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Drill the cable holes
Clamp R over scrap and drill two 3/4 in holes through it, 4 and 8 in from the left end and 1-3/4 in up from the bottom edge. Sand the hole edges smooth.
02 Attach the backstop and front
Drill and countersink 3 holes up through B along each long edge, centred on where R and F will stand. Glue their bottom edges, stand them flush at the back and front, and drive 3 screws into each.
03 Add the sides
Glue each S between F and R on the side edges of the base and drive 2 screws up through B into each.
04 Finish
Sand, round the edges, and apply your finish. Feed the cables through once it is fully dry.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

SHELVES & STORAGE · CONFIDENT BEGINNER
The Open Slat Laundry Hamper
A tall, airy hamper with five rows of 1x3 slats on corner posts and a plywood floor. A fabric liner keeps clothes off the wood.
↔︎ 18 × 14 × 25-1/2 in✓ Cut list
View plan & downloadQuick PDFDownload

SHELVES & STORAGE · CONFIDENT BEGINNER
The Two Tier Letter Trays
Two open-front paper trays joined by four slim posts, so mail and letter-size paper sort into two levels.
↔︎ 15-1/2 × 10-1/2 × 7 in✓ Cut list
View plan & downloadQuick PDFDownload

SHELVES & STORAGE · CONFIDENT BEGINNER
The Fresh Start Bathroom Shelf
A wall shelf with two shelves and a towel bar below, hung on two hidden rails screwed into the wall studs.
↔︎ 24 × 7-3/4 × 20 in✓ Cut list
View plan & downloadQuick PDFDownload