
GRAINBENCH ORIGINALS
The Open Slat Laundry Hamper
A tall, airy hamper with five rows of 1x3 slats on corner posts and a plywood floor. A fabric liner keeps clothes off the wood.
18 in W × 14 in D × 25-1/2 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x3 and 1x2 boards, 2x2 lumber and 1/2 in plywood.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 2x2 board, 8 ft: For P corner posts
- 1 x 2x2 board, 4 ft (or an offcut at least 26 in long): For P corner posts
- 3 x 1x3 board, 8 ft: For E end slats, L long slats
- 1 x 1x3 board, 4 ft: For E end slats
- 1 x 1x2 board, 4 ft: For C floor cleats
- 1 x 1/2 plywood, 2 ft x 2 ft panel: For B floor
- #8 x 1-1/2 in flathead wood screws: 80, plus a few spares
- #6 x 1-1/4 in flathead wood screws: 14, plus a few spares
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
- Finish: About 1 L (1 quart) of paint, stain or clear water-based polyurethane
- Fabric liner: A removable cloth laundry liner about 16 x 12 in
Before the first cut
Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 18 in; Sander or sanding block; Safety glasses and hearing protection; Spacers: a 1/2 in scrap and two 3-1/4 in blocks.
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
The posts are cut to 25 in for 1/2 in plywood. If your plywood is thinner or thicker, make them 25-1/2 in minus its actual thickness so they finish flush with the top slats. Measure the plywood first and cut the posts P to suit. Cut all the slats of each length at once so they match.
For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
27 parts from 2x2, 1x3, 1/2 plywood and 1x2.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| P | Corner posts | 4 | 2x2 | 25 | 1-1/2 | 1-1/2 |
| L | Long slats | 10 | 1x3 | 18 | 2-1/2 | 3/4 |
| E | End slats | 10 | 1x3 | 12-1/2 | 2-1/2 | 3/4 |
| B | Floor | 1 | 1/2 plywood | 16-1/2 | 12-1/2 | 1/2 |
| C | Floor cleats | 2 | 1x2 | 13-1/2 | 1-1/2 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Build the front and back
Lay two P on a 1/2 in spacer and place five L across them, using the 3-1/4 in blocks to set the gaps. Glue each contact and drive 2 screws per post, 1 and 1-3/4 in up from each slat's bottom edge. Make the back the same way.
02 Add the ends
Stand the front and back up and fit the E slats between them at the same heights. Glue and drive 2 screws per post, this time 1-1/4 and 2 in up from each slat's bottom so they miss the first set. Check it is square.
03 Fit the cleats and floor
Fit each C inside the bottom long slat between the posts, 1/2 in up from the bottom, and screw through the slat into it with 4 screws. Turn the hamper over, drop B in below the cleats and drive 3 screws up into each.
04 Finish
Sand every slat edge smooth so nothing snags clothes, apply your finish, and drop in the liner.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

SHELVES & STORAGE · CONFIDENT BEGINNER
The Two Tier Letter Trays
Two open-front paper trays joined by four slim posts, so mail and letter-size paper sort into two levels.
↔︎ 15-1/2 × 10-1/2 × 7 in✓ Cut list
View plan & downloadQuick PDFDownload

SHELVES & STORAGE · CONFIDENT BEGINNER
The Fresh Start Bathroom Shelf
A wall shelf with two shelves and a towel bar below, hung on two hidden rails screwed into the wall studs.
↔︎ 24 × 7-3/4 × 20 in✓ Cut list
View plan & downloadQuick PDFDownload

SHELVES & STORAGE · CONFIDENT BEGINNER
The Reading Corner Book Bin
A low, open floor bin that shows off picture books face-out. Sloping sides make it easy for small hands to reach in.
↔︎ 22 × 12 × 16 in✓ Cut list
View plan & downloadQuick PDFDownload