
GRAINBENCH ORIGINALS
The Kitchen Recipe Box
A small lift-off-lid box for 4 x 6 or 3 x 5 recipe cards. Two cleats under the lid keep it centred, and a plywood bottom is glued on underneath.
9 in W × 6 in D × 6-1/4 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x6 and 1x2 boards, 1/4 in plywood and 1/2 in plywood.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 1x6 board, 4 ft: For F front and back, S ends
- 1 x 1x2 board, 4 ft (or an offcut at least 8-1/8 in long): For C lid cleats
- 1 x 1/4 plywood, 2 ft x 2 ft panel (or an offcut at least 6 x 9 in): For B bottom
- 1 x 1/2 plywood, 2 ft x 2 ft panel (or an offcut at least 6 x 9 in): For T lid
- 1-1/4 in coarse-thread pocket-hole screws: 8, plus a few spares
- 3/4 in brads: About 12, for the bottom
- Knob: 1 small knob (about 1 in) with a screw short enough for a 1/2 in lid, usually 3/4 in
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
- Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane
Before the first cut
Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 12 in; Hammer and nail set, or a brad nailer; Sander or sanding block; Safety glasses and hearing protection.
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
The plywood pieces are small, so offcuts of 1/4 in and 1/2 in plywood work perfectly. Cut the walls F and S, the bottom B and the lid T square. B and T are both 9 x 6 in; check their diagonals.
For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
8 parts from 1x6, 1/4 plywood, 1/2 plywood and 1x2.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| F | Front and back | 2 | 1x6 | 9 | 5-1/2 | 3/4 |
| S | Ends | 2 | 1x6 | 4-1/2 | 5-1/2 | 3/4 |
| B | Bottom | 1 | 1/4 plywood | 9 | 6 | 1/4 |
| T | Lid | 1 | 1/2 plywood | 9 | 6 | 1/2 |
| C | Lid cleats | 2 | 1x2 | 3-1/2 | 1-1/2 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Drill the pocket holes
Drill 2 pocket holes at each end of both S on the inside face, 1 in from the top and bottom edges.
02 Build the walls
Glue the ends of each S and clamp them between the two F, flush at the top, bottom and outside. Drive 8 screws and check the box is square.
03 Add the bottom
Spread glue on the bottom edges of the walls, set the box on B with the edges flush all round, and nail the bottom on with brads about every 2 in.
04 Make the lid
Lay T face down. Glue the two C to its underside, running front to back, 1 in in from each end and 1-1/4 in in from the front and back edges. Clamp until dry. Check that the lid drops on without binding, then drill a hole in the centre of the top for the knob.
05 Finish
Sand, ease the edges, apply your finish, and screw on the knob.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

SHELVES & STORAGE · CONFIDENT BEGINNER
The Evening Charging Valet
A shallow tray for phones, keys and a watch, with a backstop drilled for charging cables. The chargers stay outside the tray.
↔︎ 12 × 7-1/4 × 4-1/4 in✓ Cut list
View plan & downloadQuick PDFDownload

SHELVES & STORAGE · CONFIDENT BEGINNER
The Open Slat Laundry Hamper
A tall, airy hamper with five rows of 1x3 slats on corner posts and a plywood floor. A fabric liner keeps clothes off the wood.
↔︎ 18 × 14 × 25-1/2 in✓ Cut list
View plan & downloadQuick PDFDownload

SHELVES & STORAGE · CONFIDENT BEGINNER
The Two Tier Letter Trays
Two open-front paper trays joined by four slim posts, so mail and letter-size paper sort into two levels.
↔︎ 15-1/2 × 10-1/2 × 7 in✓ Cut list
View plan & downloadQuick PDFDownload