
GRAINBENCH ORIGINALS
The Under Desk Foot Platform
A low, slatted footrest for under a desk. Three 1x4 slats sit on two upright runners, all from one board.
18 in W × 11-1/4 in D × 4-1/4 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x4 board.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 1x4 board, 8 ft: For R runners, T slats
- #8 x 1-1/2 in flathead wood screws: 12, plus a few spares
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
- Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane
- Non-slip strips: 2, for under the runners
Before the first cut
Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 12 in; Sander or sanding block; Safety glasses and hearing protection; Two 3/8 in spacers (scrap).
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
A 1x4 is actually about 3/4 x 3-1/2 in. Everything comes from one 8 ft board. Cut the slats T and runners R square so the platform sits flat.
For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
5 parts from 1x4.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| T | Slats | 3 | 1x4 | 18 | 3-1/2 | 3/4 |
| R | Runners | 2 | 1x4 | 11-1/4 | 3-1/2 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Attach the front slat
Stand both R on edge, parallel. Drill and countersink 2 holes at each end of a T, centred over the runners, 1 in from its front and back edges. Glue and screw it on flush with the runner fronts, 1-1/2 in in from each end.
02 Add the other slats
Fit the middle and back slats the same way, using 3/8 in spacers to set the gaps. Check all three sit level.
03 Finish
Sand all the edges smooth so socks will not snag, finish, and add non-slip strips under the runners.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

HOME & DECOR · CONFIDENT BEGINNER
The Soft Landing Blanket Ladder
A leaning blanket ladder with three flat rungs. The feet are bevelled so it rests flat at a gentle lean, and a small strap holds it to the wall.
↔︎ 29 in W × 59 in H✓ Cut list
View plan & downloadQuick PDFDownload

HOME & DECOR · CONFIDENT BEGINNER
The Sunny Corner Plant Pedestal
A small square stand that lifts a potted plant into the light. Two 1x8 boards make the top without ripping or planing.
↔︎ 14 × 14-1/2 × 22 in✓ Cut list
View plan & downloadQuick PDFDownload

HOME & DECOR · CONFIDENT BEGINNER
The Simple Lines Picture Frame
A plain, sturdy frame for a 12 x 16 in print, made with square butt joints, no mitres, and a removable plywood back.
↔︎ 14 × 1 × 18 in✓ Cut list
View plan & downloadQuick PDFDownload