Search GrainBench

Find plans, patterns, guides, materials and tools.

The Desktop Headphone Perch project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Desktop Headphone Perch

A small stand that keeps one pair of headphones off the desk. Three pieces of offcut, four screws.

8 in W × 5-1/2 in D × 11-3/4 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x6 and 1x3 boards.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 1x6 board, 4 ft (or an offcut at least 9 in long): For B base
  • 1 x 1x3 board, 4 ft (or an offcut at least 17-3/8 in long): For S stem, T top bar
  • #8 x 1-1/2 in flathead wood screws: 4, plus a few spares
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane
  • Cork and felt (optional): Thin adhesive cork for the bar and felt for the base

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 1 clamps that open to at least 12 in; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Every part is short, so offcuts work well. Choose pieces without knots at the ends. Cut the three parts square, especially the two ends of the stem S so it stands straight.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

3 parts from 1x6 and 1x3.

IDPartQtyStockLengthWidthThickness
BBase11x685-1/23/4
SStem11x310-1/42-1/23/4
TTop bar11x362-1/23/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Attach the stem

Mark the centre of B. Drill and countersink 2 holes up through the base, 1-1/2 in apart across the stem's width. Glue the bottom of S, stand it on the mark, and drive 2 screws up into it, drilling pilot holes first because these go into end grain.

02 Add the top bar

Centre T on top of the stem, drill and countersink 2 holes down through it, glue, and drive 2 screws into the stem.

03 Finish

Round the corners of the top bar, sand, and apply your finish. Add cork on top and felt under the base once it is dry.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Book Corner Pair project visualization

HOME & DECOR · CONFIDENT BEGINNER

The Book Corner Pair

A pair of L-shaped bookends. Books stand right against the upright, and a small cleat behind it braces the corner. Both come from a short 1x8 and a scrap of 1x2.

↔︎ 7-1/4 × 8-3/4 × 8 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.