
GRAINBENCH ORIGINALS
The Book Corner Pair
A pair of L-shaped bookends. Books stand right against the upright, and a small cleat behind it braces the corner. Both come from a short 1x8 and a scrap of 1x2.
7-1/4 in W × 8-3/4 in D × 8 in H
Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.
Common materials. Clear details.
1x8 and 1x2 boards.
Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.
Shopping list
- 1 x 1x8 board, 4 ft: For B bases, U uprights
- 1 x 1x2 board, 4 ft (or an offcut at least 12-5/8 in long): For C back cleats
- #8 x 1-1/2 in flathead wood screws: 6, plus a few spares
- #6 x 1-1/4 in flathead wood screws: 4, plus a few spares
- Wood glue: Small bottle of interior wood glue
- Sandpaper: 120 and 180 grit
- Finish: About 250 mL (half a pint) of paint, stain or clear water-based polyurethane
- Non-slip pads: 8 thin pads
Before the first cut
Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Drill/driver with a countersink bit; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 12 in; Sander or sanding block; Safety glasses and hearing protection.
Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.
Prepare before you cut
Stock, fitting and drilling checks
A 4 ft 1x8 is plenty for both bookends, and the cleats come from any 1x2 offcut. Cut the bases B and uprights U from the 1x8, keeping their ends square so the uprights stand straight.
For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.
Your parts at a glance
Dimensions in inches. Stock names are nominal; finished dimensions are actual.
6 parts from 1x8 and 1x2.
| ID | Part | Qty | Stock | Length | Width | Thickness |
|---|---|---|---|---|---|---|
| B | Bases | 2 | 1x8 | 8-3/4 | 7-1/4 | 3/4 |
| U | Uprights | 2 | 1x8 | 7-1/4 | 7-1/4 | 3/4 |
| C | Back cleats | 2 | 1x2 | 5-3/4 | 1-1/2 | 3/4 |
A clear way through
Keep the PDF beside you for the dimensioned drawings and drilling layouts.
01 Attach the uprights
On each B, mark a line 1-7/8 in from the back edge; this is the centre of the upright. Drill and countersink 3 holes on the line from underneath. Glue the bottom of U, stand it on the base with its back face 1-1/2 in from the back edge, and drive 3 screws up into it, drilling pilots first.
02 Add the cleats
Glue the bottom and front edge of each C and press it onto the base, tight against the back of the upright and centred side to side. Drill, countersink and drive 2 screws down through the cleat into the base.
03 Finish
Sand, ease the edges, apply your finish and stick pads under each base.
A little help along the way
You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?
More simple things to make

HOME & DECOR · CONFIDENT BEGINNER
The Under Desk Foot Platform
A low, slatted footrest for under a desk. Three 1x4 slats sit on two upright runners, all from one board.
↔︎ 18 × 11-1/4 × 4-1/4 in✓ Cut list
View plan & downloadQuick PDFDownload

HOME & DECOR · CONFIDENT BEGINNER
The Soft Landing Blanket Ladder
A leaning blanket ladder with three flat rungs. The feet are bevelled so it rests flat at a gentle lean, and a small strap holds it to the wall.
↔︎ 29 in W × 59 in H✓ Cut list
View plan & downloadQuick PDFDownload

HOME & DECOR · CONFIDENT BEGINNER
The Sunny Corner Plant Pedestal
A small square stand that lifts a potted plant into the light. Two 1x8 boards make the top without ripping or planing.
↔︎ 14 × 14-1/2 × 22 in✓ Cut list
View plan & downloadQuick PDFDownload