Search GrainBench

Find plans, patterns, guides, materials and tools.

The Low Line Media Cabinet project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Low Line Media Cabinet

A long, low open cabinet with three bays, each with a middle shelf for devices, games and baskets. Built from 1x12 boards with a plywood back.

48 in W × 11-1/2 in D × 22 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

1x12 board and 1/4 in plywood.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 2 x 1x12 board, 8 ft: For H bottom, S sides, T top, V dividers
  • 1 x 1x12 board, 4 ft: For M shelves
  • 1 x 1/4 plywood, 2 ft x 4 ft panel: For R back
  • 1-1/4 in coarse-thread pocket-hole screws: 42, plus a few spares
  • 3/4 in brads: About 45, for the back
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 1 L (1 quart) of paint, stain or clear water-based polyurethane
  • Anti-tip strap: 1, with screws suited to your wall

Before the first cut

Saw for straight crosscuts: mitre saw, or circular saw with a speed square; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 48 in; Hammer and nail set, or a brad nailer; Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Pick flat 1x12s without cupping, especially for the long top and bottom. Cut the back R after assembly so it matches your case. Cut the long top T and bottom H first, then the sides, dividers and shelves. Label each part and mark front edges.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

10 parts from 1x12 and 1/4 plywood.

IDPartQtyStockLengthWidthThickness
SSides21x1221-1/411-1/43/4
TTop11x124811-1/43/4
HBottom11x1246-1/211-1/43/4
VDividers21x1220-1/211-1/43/4
MShelves31x121511-1/43/4
RBack11/4 plywood4821-1/41/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the pocket holes

Drill 3 pocket holes at each end of H and every M on the underside, at both ends of each V on its right face, and at the top end of each S on its inside face.

02 Fit the bottom between the sides

Glue the ends of H and clamp it between the two S, flush with their bottoms and fronts. Drive 3 screws at each end.

03 Add the dividers

Mark the top of H at 15-3/4 and 31-1/2 in from the left end of the case. Stand each V with its left face on a mark, right face to the right, glue and drive the 3 bottom screws into H.

04 Fit the shelves

Mark every side and divider 10-1/4 in up from the floor. Set each M on its marks with the pocket holes facing down, glue and drive 3 screws at each end.

05 Attach the top

Set T on the case flush at the ends and front. Drive the 6 screws from the sides and the 6 from the tops of the dividers up into it.

06 Back, finish and anchor

Square the case, cut R to fit below the top, and glue and nail it on about every 4 in. Sand, finish, and fasten the anti-tip strap into a wall stud before setting a TV on top.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Slim Utility Shelf project visualization

SHELVES & STORAGE · CONFIDENT BEGINNER

The Slim Utility Shelf

A tall, narrow shelf for a laundry room, pantry or bathroom corner, with four fixed shelves and a plywood back. It is anchored to the wall.

↔︎ 18 × 11-1/2 × 60 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.