Search GrainBench

Find plans, patterns, guides, materials and tools.

The Weekend Record Cabinet project visualization
3D visualization based on the plan · Not a photograph of a built prototype

GRAINBENCH ORIGINALS

The Weekend Record Cabinet

A plywood cabinet sized for 12 in records: two bays, each split by a fixed shelf, give four record cubbies with room to flip through.

30 in W × 14-3/4 in D × 30 in H

Confident beginnerAlways free

Printable drawings, a labelled cut list and step-by-step assembly instructions. No account or email required.

Common materials. Clear details.

3/4 in plywood and 1/4 in plywood.

Use straight, dry stock and check its actual thickness. The PDF lists quantities, hardware sizes, part labels and the cutting layout.

Shopping list
  • 1 x 3/4 plywood, 4 ft x 8 ft sheet: For H bottom, M shelves, S sides, T top, V divider
  • 1 x 1/4 plywood, 4 ft x 4 ft panel: For R back
  • 1-1/4 in coarse-thread pocket-hole screws: 30, plus a few spares
  • 3/4 in brads: About 40, for the back
  • Edge banding (optional): About 20 ft of iron-on veneer tape for the front edges
  • Wood glue: Small bottle of interior wood glue
  • Sandpaper: 120 and 180 grit
  • Finish: About 1 L (1 quart) of paint, stain or clear water-based polyurethane
  • Anti-tip strap: 1, with screws suited to your wall

Before the first cut

Circular saw with a straight-edge guide, or have the store cut the plywood; Pocket-hole jig set for 3/4 in stock, with its stepped bit and a #2 square driver bit; Drill/driver; Tape measure, pencil and a combination or speed square; 2 clamps that open to at least 30 in; Hammer and nail set, or a brad nailer; Household iron (for edge banding); Sander or sanding block; Safety glasses and hearing protection.

Digitally checked; not physically built or load-tested. Follow the PDF’s fixing, stability and inspection instructions.

Prepare before you cut

Stock, fitting and drilling checks

Everything solid comes from one 4 x 8 sheet of 3/4 in plywood; ask the store to rip it into 14-1/2 in strips if you do not have a way to cut long straight lines. Choose a sheet with a smooth face. Rip the sheet into 14-1/2 in strips, then crosscut the parts. Mark the best face of each piece and the front edges.

For ordinary wood screws, make a clearance hole in the first piece and a pilot in the receiver; use the screw maker’s bit sizes. Pocket holes use the jig’s own setup. Trial the actual joint on scrap, including the countersink, then check both faces for tips before fastening the project.

Your parts at a glance

Dimensions in inches. Stock names are nominal; finished dimensions are actual.

8 parts from 3/4 plywood and 1/4 plywood.

IDPartQtyStockLengthWidthThickness
SSides23/4 plywood29-1/414-1/23/4
TTop13/4 plywood3014-1/23/4
HBottom13/4 plywood28-1/214-1/23/4
VDivider13/4 plywood28-1/214-1/23/4
MShelves23/4 plywood13-7/814-1/23/4
RBack11/4 plywood3029-1/41/4

A clear way through

Keep the PDF beside you for the dimensioned drawings and drilling layouts.

01 Drill the pocket holes

Drill 3 pocket holes at each end of H and both M on the underside, at both ends of V on its right face, and at the top end of each S on its inside face. If you are edge-banding, iron the tape onto the front edges now.

02 Fit the bottom and divider

Glue and clamp H between the sides, flush at the bottom and front, and drive 6 screws. Mark H 14-5/8 in from the left of the case, stand V with its left face on the mark, and drive its 3 bottom screws.

03 Fit the shelves

Mark the sides and divider 14 in up from the floor. Set each M on its marks, pocket holes down, glue and drive 3 screws at each end.

04 Attach the top

Set T on the case flush at the ends and front, then drive the 6 screws from the sides and 3 from the divider up into it.

05 Back, finish and anchor

Square the case, cut R to fit below the top, and glue and nail it on about every 4 in. Sand, finish, and fasten the anti-tip strap into a wall stud.

A little help along the way

Read the drawings and cut listExplore wood and panel materials

You may sell your finished makes. Please keep the plan files and images with GrainBench. Plan usage terms → · Questions or corrections?

More simple things to make

The Slim Utility Shelf project visualization

SHELVES & STORAGE · CONFIDENT BEGINNER

The Slim Utility Shelf

A tall, narrow shelf for a laundry room, pantry or bathroom corner, with four fixed shelves and a plywood back. It is anchored to the wall.

↔︎ 18 × 11-1/2 × 60 in✓ Cut list

View plan & download

Quick PDFDownload

The Kitchen Recipe Box project visualization

SHELVES & STORAGE · CONFIDENT BEGINNER

The Kitchen Recipe Box

A small lift-off-lid box for 4 x 6 or 3 x 5 recipe cards. Two cleats under the lid keep it centred, and a plywood bottom is glued on underneath.

↔︎ 9 × 6 × 6-1/4 in✓ Cut list

View plan & download

Quick PDFDownload

GRAINBENCH ORIGINALS

Build something lovely.

This plan is free. A little support is always optional.

Download for free ↓

Optional support via PayPal USD

Optional support opens PayPal in a new tab. Review the recipient, amount and currency there. No payment is needed to download.

You may sell your finished makes. Pattern files may not be resold or shared.

GRAINBENCH

Let’s make it easier.